- Licensed & Insured
- 20+ Years Experience
- Fast Response
- Stillwater, MN
Erick Marshall Electric has provided licensed wiring services in Stillwater, MN since 2002. We specialize in residential rewiring and electrical wiring upgrades for homes across Stillwater and the east metro, including the area’s many older and historic properties. Whether you need a full home rewire, knob and tube replacement, aluminum wiring upgrades, or new circuits for a renovation, our licensed master electrician team handles the job from permit to final inspection. We are local to Stillwater, not a chain dispatching from the Cities — and we treat every home with the care and attention it deserves.
If you are planning a kitchen remodel, adding a room, or finishing a basement, updating your wiring during the project is the smartest time to do it. Older Stillwater homes often have wiring that was installed decades ago and was never designed to carry the load of a modern kitchen or home office. We work with homeowners to plan electrical layouts for renovations from the start, running new wire while walls are open to save time and avoid patching later.
Our electricians ensure your new wiring matches the rest of your home and complies with all current Minnesota electrical codes and Washington County permit requirements. We can add circuits for recessed lighting, smart home automation, USB outlets, and modern data connections at the same time. Many of Stillwater’s older homes also have limited outlets and undersized circuits — renovation is the right moment to fix both. As your local Stillwater electrician, we know the specific conditions common in east metro homes and plan accordingly.
Safe wiring means more than just the cables behind the walls. Older Stillwater homes frequently have ungrounded two-prong outlets and circuits that never received proper GFCI protection. During a rewiring project, we ensure your entire system is properly grounded, providing a safe return path for excess electricity during a surge or short circuit.
We install GFCI outlets in all required locations: kitchens, bathrooms, garages, outdoor areas, and anywhere near a water source. We also install AFCI (arc fault) protection in bedrooms and living areas, which current Minnesota electrical code now requires in new and updated circuits. These devices detect dangerous arcing conditions before they can cause a fire. Our team ensures every room has enough outlets in the right locations so you can stop relying on extension cords and overloaded power strips for good.
Modern appliances demand more power than the wiring in most older Stillwater homes was built to provide. Electric ovens, refrigerators, space heaters, window air conditioners, and home EV chargers all require dedicated circuits to operate safely. Running these devices on shared, undersized wiring causes breakers to trip, shortens appliance life, and creates real fire risk.
As part of our wiring services, we install dedicated circuits sized correctly for each high-demand device. This means your kitchen lights no longer flicker when the microwave starts, and your laundry room runs without tripping the rest of the house. We add dedicated circuits for home offices, entertainment centers, EV chargers, and heated floors as well. By distributing the electrical load across properly sized, individual circuits, your system runs cooler, safer, and more reliably for years to come.
Before any wiring or rewiring project, Erick Marshall Electric performs a thorough inspection of your home’s existing electrical system. We look for signs of heat damage, deteriorated insulation, improper connections, double-tapped breakers, and wiring that has been modified without permits. Our goal is to find the hidden problems before they become emergencies.
If you are experiencing burning smells, flickering or dimming lights, outlets that feel warm to the touch, or breakers that trip under normal loads, call us before the problem gets worse. These are all warning signs of wiring that is struggling or failing. We have been diagnosing electrical problems in Stillwater homes since 2002 and carry the tools to test your circuits without unnecessary damage to your walls. After the inspection, we give you a clear, honest report on what we found and what needs to be done, with no pressure to do more than you need.
Knob and tube wiring and aluminum branch circuit wiring are two of the most common electrical issues we find in Stillwater’s older homes. Many properties built before the 1960s still have at least some original knob and tube wiring in place. While not automatically dangerous, knob and tube wiring has significant limitations: it lacks a ground wire, offers no arc fault protection, and the original cloth insulation becomes brittle and cracks with age. Insurance companies in Minnesota increasingly refuse to cover homes with active knob and tube wiring, and lenders may require replacement before closing.
One critical risk specific to knob and tube wiring: it must never be buried under insulation. The wiring relies on open air circulation to dissipate heat. If your attic has knob and tube runs and you are planning to add blown-in insulation, the wiring in that area must be replaced first. This is a common situation in Stillwater’s older neighborhoods and something we handle regularly.
Aluminum branch circuit wiring, installed commonly in homes built between 1965 and 1973, presents a different problem. Aluminum expands and contracts with temperature changes more than copper does, causing connections at outlets and switches to loosen over time. Loose aluminum connections can arc, overheat, and start fires. We replace aluminum branch wiring with modern copper and use AlumiConn connectors where individual connection upgrades are the right solution.
Erick Marshall Electric specializes in replacing both of these systems throughout Stillwater and the east metro. We work carefully in historic properties to minimize damage to original trim, plaster, and hardwood floors. Our team has replaced knob and tube and aluminum wiring in Stillwater homes since 2002, and we understand how to do it efficiently while respecting the character of the space.
Wiring services from Erick Marshall Electric include full home rewiring, partial rewiring for renovations, knob and tube wiring replacement, aluminum wiring replacement, dedicated circuit installation, GFCI and AFCI outlet upgrades, grounding improvements, and new circuits for additions or appliances. Every project includes the required state electrical permit and a final inspection. We handle all coordination with Washington County and your utility provider.
Common signs include: breakers that trip repeatedly under normal loads, lights that flicker or dim when an appliance starts, outlets or switch plates that feel warm, a burning or plastic smell near the panel or outlets, two-prong ungrounded outlets throughout the home, or a visible knob and tube or aluminum wiring system. If your home was built before 1970 and has never had a full electrical update, a professional inspection is a smart first step. Erick Marshall Electric offers wiring inspections for Stillwater homeowners. Call (651) 426-3889 to schedule.
No. Knob and tube wiring must never be buried under insulation. The wiring relies on open air to release heat, and covering it creates a fire hazard. If your Stillwater home has knob and tube wiring in the attic and you want to add insulation, that wiring needs to be replaced first. This is one of the most common situations we address in Stillwater’s older neighborhoods.
The cost of rewiring a home in Stillwater depends on the home’s size, age, and the extent of the work. A partial rewire for a renovation or room addition is significantly less than a full home rewire. Full rewiring of a typical Stillwater home ranges from $8,000 to $20,000 or more depending on square footage, number of circuits, wall access, and whether a panel upgrade is needed at the same time. Erick Marshall Electric provides free estimates with transparent, itemized pricing. Contact us for a quote specific to your home.
Yes. Minnesota state law requires an electrical permit for all rewiring work. Washington County also requires that the work be performed by a licensed electrician. Erick Marshall Electric pulls every required permit and schedules the state inspection as part of every job. You do not need to contact the county or your utility company separately, we handle all of it.
Yes, and it is one of our specialties. Stillwater has a significant number of homes built before 1960, many of which still have original or modified knob and tube wiring, outdated panels, limited outlets, and circuits that have been added to over the decades without consistent documentation. Erick Marshall Electric has been working in Stillwater homes since 2002 and understands how to rewire historic and older properties carefully, minimizing disruption to original plaster, trim, and hardwood while bringing the electrical system fully up to current code.
Is your home’s wiring overdue for an upgrade? Erick Marshall Electric has provided trusted wiring services in Stillwater, MN since 2002. Whether you need a full home rewire, knob and tube replacement, or new circuits for a renovation, our licensed team handles everything from the permit to the final inspection
Call 651-426-3889 or request a free estimate online to get started.
